Home
Drivers
Network
NetGear
NetGear KWGR614 54 Mbps Wireless Router Firmware 1.0.1.10.17WW

NetGear KWGR614 54 Mbps Wireless Router Firmware 1.0.1.10.17WW

Publisher's description
File details
Antivirus report
"This version is for use OUTSIDE North Am..."
Published by NetGear on 26 Mar 2010
Publisher support

  • Size:

    1.76 MB

  • License:

    Freeware

  • OS:

    Windows

  • Price:

    $0

  • Updated:

    26 Mar 2010

  • Downloads:

    89 (1 last week)
This version is for use OUTSIDE North America Only!

Note: Do not upgrade the firmware using a wireless connection. Please perform firmware upgrade with “wired” or Ethernet connection only.

Bug Fixes:

1. Fixed a Block Site issue which caused Internet re-connection in the DHCP mode.
2. Fixed the Web GUI issue that changing the wireless setting might fail the Web GUI access after router reboot.
3. Fixed a LAN IP address re-assignment bug under a specific LAN/WAN IP address conflict condition.
4. Increased the NAT UDP table to 2048 entries, and shortened the UDP session timeout to 5 minutes for NAT.
5. Disabled the SIP ALG and NAT Port Reservation to avoid an one-way voice problem with the SIP phones

Known Issues:

1. Video and Audio of ICQ5 connection cannot be established.

To Upgrade:

Note: Do not upgrade the firmware using a wireless connection. Please perform firmware upgrade with “wired” or Ethernet connection only.

1. Write down all the settings which you changed from the default values, since you may need to reenter them manually.
2. Download using the button below to a convenient place such as your desktop.
3. Log in to the router using a Web broswer. The URL is http://192.168.1.1 ( if you did not change the router’s IP address ).
4. Click Maintenance > Router Upgrade
5. Click Browse and find the file you just downloaded.
6. Click Upload. Do not interrupt the upgrade while the router does this step. The router reboots when the upgrade is done.
7. After the router boots up, log in the router again.
8. If you would like to check that the upgrade was successful, log in to the router again at http://192.168.1.1, and check the firmware version.

Recovery Procedure:

In case the flash image is damaged (because of improper or interrupted upgrade process, or bad firmware image programmed by the open source developers, etc), you can reloading the firmware via TFTP following the procedure below:

1. Power off the unit
2. Press and hold the RESET button at the rear panel
3. Power on to reboot the unit
4. Monitor the Test LED, and keep holding the RESET button until the Test LED changes from blinking to steady ON (which means the boot loader has entered the TFTP recovery mode)
5. Connect the PC to the LAN port of the unit
6. Transmit the firmware image file to the unit:
7.
* For Windows PC, enter the DOS command:
tftp -i 192.168.1.1 PUT KWGR614_XXX.bix
* For a Linux PC, use the command:
tftp -m binary 192.168.1.1 -c put KWGR614_XXX.bix

where the “192.168.1.1” is the unit’s LAN IP address and “KWGR614_XXX.bix” is the firmware image file to transmit.
8. Monitor the Test LED. When it starts blinking, the recovery procedure is complete.
9. Power cycle to reboot KWGR614
(*Repeat the above steps if the procedure is interrupted or failed)

Before installing version 1.0.1.10.17WW of NetGear KWGR614 54 Mbps Wireless Router Firmware for Windows make sure this is the latest version available and that it works with your current operating system and device model. If the driver contains release notes ("readme" files) proceed with reading them first. Second recommended step is creating a restore point to help you later on in case you install the wrong device driver. Note that some drivers will work instantly after installing them, but others will require a system restart in order to function properly.

As an alternative, you can simplify the process of installing the latest versions for your drivers by using a program to scan all your drivers and compare them with the latest available versions from the manufacturers. We recommend Driver Scanner from Uniblue for such a task. Download it and run a free driver scan here.

Antivirus information

Download3K has downloaded and tested NetGear KWGR614 54 Mbps Wireless Router Firmware on 18 May 2012 with some of Today's best antivirus engines and you can find below, for your convenience, the scan results:

  • Bitdefender:

    Clean

  • NOD 32:

    Clean

  • Avira:

    Clean

  • Kaspersky:

    Clean
NetGear KWGR614 54 Mbps Wireless Router Firmware Antivirus Report
Complete antivirus report

Notifications

Your email:
Friends email:

Related press releases

Download here
User rating
0/5
(0 votes)
Your opinion